Blacksmith: You Are Making Mjolnir For The Forging Exam? Chapter 316 New Alloy Material

Although the materials from the warehouse were not too precious, each of them was of a certain degree of rarity. If he were to go around and collect them, it would take at least a week to gather a whole set.

Furthermore, the armory's warehouse had given him about three sets of each material, which greatly increased Wu Mo's margin for error in forging.

Although this was only his first attempt, if he could succeed on his first try, he would be able to save a lot of ti.

What surprised him the most was that such treatnt was given even to ordinary staff mbers.

One could see how rich the armory was.

With a thought, Wu Mo put the materials in his Interspatial Ring.

After confirming that the dormitory door was locked from the inside, Wu Mo sat on the edge of the bed and slowly closed his eyes to calm his mind. After a while, he had seemingly fallen asleep and could no longer sense any movent around him.

By the ti he recovered and opened his eyes again, he was in a boundless chaotic space with dark purple light floating around.

At the center of the chaotic space, there were familiar working tables, furnaces, casting tools, and other instrunts.

Wu Mo walked up quickly and waved his right hand. The next mont, a small mountain of rare materials appeared before him.

"Let's start..."

Wu Mo muttered to himself as he squinted and looked at the materials in front of him that were emitting a faint glow.

He quickly put on the Craftsman's Gloves and imdiately began to process the materials.

Wu Mo was not trying to cast a device for the Three-dinsional Maneuver Gear, but an exoskeleton armor that wrapped around the wearer and protected him or her.

According to his design, the Three-dinsional Maneuver Gear would perfectly cover the chest, lower abdon, hands, and feet of the wearer.

There was no design for the head as it would block the wearer's vision.

After all, the Three-dinsional Maneuver Gear was known for its flexibility. If there was a loss of vision, it would likely lead to other problems.

To achieve high mobility and flexibility, the material of the exoskeleton armor had to be light, and its thickness should not exceed three centiters!

Moreover, the toughness and hardness needed to reach a very high standard so that it could be used for protection.

These almost unreasonable requirents ant that the materials used to cast the armor had to be carefully selected.

Unfortunately, Wu Mo had not been able to find the right materials during the few months he had been researching and developing the Three-dinsional Maneuver Gear.

If it was too heavy, it would greatly reduce the gear's mobility.

The other way around, it would be difficult to have a high level of protection.

Even many of the patented alloys could not et his requirents.

Wu Mo had no choice but to forge an alloy that was suitable for the gear's armor himself. He had learned how to cast the new alloy from the docunt provided by the system.

Despite having the idea, he could not implent it when he was at the Fifth Research Departnt.

Since the new alloy casting thod was too complicated, it required the help of various instrunts. With the Fifth Research Departnt's current hardware, it was impossible to complete it.

Furthermore, the Research Departnt's material library was not comprehensive enough, and it could not provide the appropriate materials.

Wu Mo's idea could only be realized when he arrived at the armory.

Just like that, Wu Mo began to work on his own understanding while reviewing the alloy forging thod in the docunt.

He wanted to use these materials to create an alloy called polyethylene alloy. It was a material that was resistant to corrosion, impact, and it had high hardness.

If Wu Mo could successfully forge it this ti, the exoskeleton armor for the Three-dinsional Maneuver Gear would be close to completion.

However, even though he had already learned the core skill of alloy forging, the actual operation was still highly challenging.

The process was extrely complicated. Not only did it require the transfer of the solution, but the polyethylene needed to be extracted from the armory's material warehouse and processed into high-molecular-weight polyethylene through tower peration.

He still needed to use the furnace to calcinate another type of alloy with good compatibility. Finally, he would need to fuse the extracted high-molecular polyethylene with the other type of alloy and put them through a special process before he could obtain the final polyethylene alloy.

During this ti, Wu Mo had to do a lot of preparation work. The final step, the fusion of polyethylene and alloy, required the help of the modern equipnt in the research and developnt plant.

To complete the original version of the alloy, he had to deal with every detail.

Even if Wu Mo handled everything flawlessly, it would still take about two days to get the final product.

Although the road ahead was filled with difficulties, it did not shake Wu Mo's determination.

He wiped the fine sweat on his forehead and continued with his work.

About 40 minutes later, Wu Mo finally finished mixing the solution for extracting high-molecular polyethylene.

At this mont, the small mountain of materials beside the workbench was almost half gone.

With a sigh of relief, Wu Mo imdiately poured the light green solution into the permoter. After adjusting the permoter's mode, he returned to the workbench and continued to deal with other things.

Since the forging equipnt previously did not require that kind of material to be obtained through peration, the Divine-grade Forging Space did not have the corresponding equipnt.

This ti, with a request, the space imdiately unlocked the corresponding area.

It was just that activating the permoter cost him 1,000 points, hence Wu Mo was not quite used to it.

Ever since he beca stronger, he had not exchanged points for anything in the system store for a long ti.

Thinking back to when he was in the Divine Arms Academy, he would often exchange points for spirit power potions and spend his days counting points.

He glanced at the number in the column representing his points on the system interface. It was 276,829.

Well, it was still stable.

Wu Mo focused his attention back on the work table. He brought a few tals to the furnace and prepared to forge the alloy that was to be fused with polyethylene.

The 12 fire outlets outside the fine grade furnace were constantly emitting red light. Even though Wu Mo had not used it for a while, the flas inside were still rising and producing heat waves.

"Let's begin... Once everything is in place, I should be able to create polyethylene alloy by tomorrow."

Wu Mo placed his right palm on the fire and imdiately mobilized his spirit power.

The next mont, the temperature of the furnace rose sharply, and a blinding light spread. He squinted subconsciously and did not forget to throw in the fist-sized molybdenum.

The casting of alloys was equally complicated and boring.

Not only did Wu Mo need to control the fla temperature in the furnace for a long ti, but he also needed to put in various auxiliary materials such as oxidizers and reducing agents in ti.

It would only be considered a success when all the various tals were fused, each property t the standard, and the impurity rate was less than three thousandths.

However, Wu Mo had already practiced the process of forging tal hundreds and thousands of tis. This kind of difficulty was nothing to him, but it was certainly boring.

This process lasted for a long ti. After about two hours, Wu Mo finally completed the fusion of the materials in the furnace.

The alloy was already being removed continuously. It would probably cool down in another ten minutes or so.